How to Sew a Zipper on Shirt
Sewing is an art that every kid wants to learn and every adult wants to master. There is no one who does not like sewing. It is very easy to use and you can make the clothes that you want without spending a single penny.
Sewing a zipper on a shirt is a very simple operation. It may take you a little longer than usual because you will have to perform some measurements before you start.
If you are a beginner and don’t know how to sew a zipper on a shirt, then you are at the right place. In this post, I m am going to show you simple steps of how to sew a zipper on the shirt in the fastest and easiest possible way.
Needle – You need to thread it before you start sewing. There are many types of needles. The most common type is called an embroidery needle. You can buy it at any craft store.
Presser Foot – This is an attachment that you place on your machine and it allows the presser foot to travel down without dragging the fabric with it. You can find it at a sewing machine shop or online.
Needle Plate – This is a piece of metal that goes under the presser foot. It keeps your thread from getting caught in the moving parts of your sewing machine.
Straight Stitch Foot – This is the tool that is used to sew zippers. It is available in various lengths. You can also get a special plastic foot. It is available at most sewing machine stores.
Zipper – You will need a regular zipper or a specialty one.
Shirt – Any type of shirt would work.
Thread Sewing Machine – You will need one that has a straight stitch foot.
How to Sew a Zipper on Shirt Step by Step
Here is a simple step-by-step method to sew a zipper on a shirt.
Step 1: Materials
What you’ll need to do this project:
Step 2: Find the Right Thread
Thread is a very important component of any sewing project. Thread is the string that sews your fabric together.
To get the right thread, you’ll need to find one that is compatible with the material you’re using. For this project, we’re using a regular thread.
Step 3: Decide on a Length
You’ll want to cut the thread in half. One half will be used for stitching and the other half will be left to finish the job.
For this project, we’re using a 60 cm (24 inches) length.
Step 4: Fold the Thread
Now you’ll fold your thread in half so you can use it. Once you have a few inches of the thread, you’ll wrap it around your finger and fold it down towards the center.
Step 5: Tie the thread
Tie the two ends of the thread together.
The end result should look like this:
Step 6: Cut off the Excess Thread
Your finished thread should now be ready to stitch.
Step 7: Place the Fabric Pieces
Place the pieces of the fabric on your work surface. Make sure that the right sides of the fabric pieces are facing you.
Step 8: Pin the Fabric
Pin the two pieces of fabric to each other. We’re going to pin the ends of the shirt together.
Step 9: Stitch the Shirt
Now, you’re going to thread the needle and then sew the first and last stitches of the shirt together.
Make sure you’re using a tight stitch.
Step 10: Repeat for the Rest of the Shirt
Once you’ve finished the first half of the shirt, you’ll turn your work so the right side is facing you. You’ll do the same thing for the second piece of fabric.
Step 11: Trim the Threads
Trim the thread at the edges of the shirt.
Step 12: Turn It Inside out
Now that you’ve finished the first half, turn the shirt inside out. Repeat steps 8-12 to finish the second half.
Step 13: Pull the Threads to the Back of the Shirt
Use the ends of your thread to pull the thread up to the back of the shirt.
Step 14: Make the Zipper
You’ll now be creating a zipper. Begin by cutting the zipper tape. This is a very thin plastic, but it’s durable and good for use as a zipper.
Step 15: Create the Slider
Now you’ll create the slider. This will be the piece that closes the zipper.
Step 16: Put the Slider Onto the Zipper
Put the slider onto the zipper. You’ll start with the closed end of the zipper. Make sure you have the right end facing you when you do this.
Step 17: Attach the Slider
Attach the slider to the zipper. Make sure you have the slider pointing away from you.
Step 18: Put the Zipper Tape on the Shirt
Now you can put the zipper tape on the shirt. Once you’ve attached it, make sure to smooth it out.
Step 19: Pin the Zipper Tape
Pin the zipper tape to the fabric.
Step 20: Stitch the Zipper Tape
You’ll then sew the zipper tape to the fabric.
Step 21: Cut the Zipper Tape
Now you’ll cut off the excess zipper tape.
Step 22: Pull the Thread to the Back of the Shirt
Pull the thread up to the back of the shirt.
Step 23: Sew the Zipper Tape to the Shirt
Now you’ll sew the zipper tape to the shirt.
Step 24: Put the Shirt Inside out
Finally, put the shirt back inside out.
Step 25: Turn the Shirt
Turn the shirt inside out again.
How to Sew a Zipper on Your Shirt by Hand
Sewing is a skill that has been used since ancient times. It is a craft that has been passed from one generation to another. Nowadays, you will find people who can sew clothes for themselves but a lot of people still cannot afford a sewing machine.
There are people who can sew by using their hands but they don’t know how to make a perfect stitch. So, this article is dedicated to these people. Here you will get all the necessary tips that will show you how to sew a zipper on the shirt by hand.
You need to use
How to Sew a Zipper on Your Shirt by Hand
Here are the step-by-step methods that show you how to sew a zipper on the shirt by hand
Step 1: Prepare for Sewing
- Cut the fabric to fit the size of your garment. Make sure you check the width and length. Don’t cut off too much from each side.
- Put the fabric on your ironing board. Then fold the raw edge of the fabric to the inside (the right side) so you can sew.
- Place the fabric next to your garment and trace around the zip. Try to leave a gap at the end of the zip to insert the zipper later.
Step 2: Sew the Zipper
- Mark the end of the zipper tape with chalk.
- Fold the raw edge of the zipper inside so it will be attached to your fabric.
- Pin the zipper.
- Using your seam ripper, cut along the marked lines.
- Stitch the zipper into the fabric. Use the line on the back of the zipper as your guide.
- Once the zipper is sewn, flip it over.
- Unfold the zipper and iron the raw edges.
- Insert the zipper.
- Hand stitches the opening shut.
- Do not use a machine to sew the zipper.
- Sew along the line on the back of the fabric.
- Turn the shirt inside out.
- Hand stitches the other side of the zipper.
Step 3: Finish Sewing
- Fold the raw edge of the fabric.
- Fold the raw edge of the fabric again and pin it.
- Stitch along the marked line.
- Remove the pins.
- Turn the shirt right side out.
- Hand stitches the opening shut.
After completing this process, you will be able to sew a zipper on a shirt by hand. There are different types of zippers that can be used on shirts but this is the easiest one. If you are unable to sew a zipper, then you can easily get the one that is available at the nearest shop.
Sewing Machines vs Handsewing
Sewing machines can make a lot of sewing projects a lot easier, but they’re still not the best way to make clothing. Sewing by hand is actually a more accurate process and has many other benefits.
Hand sewing is much more involved than sewing with a machine. You have to make sure you have a good eye for detail, your hands are coordinated, and you’re able to keep track of which fabric is right side up and which is upside down.
How do I make sure the zipper is sewn on the right side of the shirt?
If you want the zipper to appear on the right side of the shirt, you will need to sew the bottom of the zipper to the right side of the shirt. This can be done in two different ways. The first way is to sew the zipper through the fabric. The second way is to sew the zipper to the right side of the fabric and then sew the sides of the fabric together.
How do I make sure the zipper won’t come undone?
Sewing a zipper in place is not an easy task, so it is important that you follow the instructions exactly. If you aren’t sure how to do this, contact a seamstress who is experienced with sewing zippers.
How do I prevent the zipper from coming undone?
To prevent the zipper from coming undone, you will need to sew the top of the zipper to the back of the shirt. This can be done in two different ways. The first way is to sew the zipper to the back of the shirt. The second way is to sew the sides of the fabric together and sew the top of the zipper to the back of the fabric.
How do I sew the sides of the zipper together?
Sew the side of the zipper into the top and bottom pieces of the fabric.
What do I do if the zipper doesn’t stay on the shirt?
If the zipper doesn’t stay on the shirt, you will need to do the following:
-Use a hot iron.
-Make sure that you have the right size needle.
-Make sure that the fabric is on a stable surface
Now, I think you will be able to learn how to sew a zipper on your shirts. So, these are some of the best tips for sewing a zipper on your shirts.
If you are new to this, then you can read our article on How to sew a button on your clothes. This is the simplest and easiest way to sew a zipper on a shirt.
Now, you can make your own t-shirt and add your own style to it. I am sure this method will help you to make your own t-shirt easily.